Software, Driver and Data Downloads

The files on this page must be “saved to disk” and then unzipped or installed before use.  When you click on a link, you will be taken to our ShareFile® site where you will be asked for some basic information and then you will be able to download the file requested.

M-TEST 7

Magtrol’s M-TEST 7 is a state-of-the-art motor testing program for PC (Windows® 7 SP1) based data acquisition. Used with a Magtrol Programmable Dynamometer Controller, M-TEST 7 works with any Magtrol Dynamometer or In-Line Torque Transducer to help determine the performance characteristics of a motor under test. Up to 63 parameters are calculated and displayed utilizing M-TEST 7’s feature-rich testing and graphing capabilities.

Download free 30 day trial of M-TEST 7 Motor Testing Software.

M-TEST 7 Viewer allows the user to create and modify test setups, and view, graph and compare data – everything standard M-TEST 7 does except perform tests. Free download, unlimited use.

M-TEST 7 Viewer


M-TEST 5.0 to M-TEST 7 Setup Conversion

This program will take an existing M-TEST 5.0 Setup File and convert it to M-TEST 7 format. There are many differences in the two setup files, so most, but not all, of the information will be converted.

The following settings will convert:

  1. 1. Controller hardware
  2. 2. Channel 1 and Channel 2
  3. 3. Power supply
  4. 4. Power measurement
  5. 5. Digital I/O
  6. 6. Test configurations
  7. 7. PID
  8. 8. Data logging

Please review the M-TEST 7 setup and make any corrections before running the test.

M-TEST 5.0 to M-TEST 7 Setup Conversion Program


Torque 10

Magtrol’s TORQUE 10 Software is an easy to use Windows® executable program, used to automatically collect torque, speed and mechanical power data from Magtrol Torque Transducers by using the Model 3410 or Model 3411 Torque Transducer Display. The data can be printed, displayed graphically or quickly saved as a Microsoft® Excel spreadsheet.

Torque 10


TS1XX Torque Sensor USB Drivers


3411 USB Drivers

The correct device drivers are dependent on the unit’s firmware. Please check the version of firmware on your unit and download the appropriate version of drivers.

Firmware REV A0-N0

Firmware REV P0+


Mag.net

The 3411 Torque Display can now be controlled via an Ethernet connection in two methods. The first is a web interface. The second allows all of the commands available through the USB interface to be used with an internet connection as well. These commands will now be formally known as the Mag.NET protocol. This is a link to a program, along with its source code, which shows how to make a connection and communicate with a 3411 unit.

Mag.NET


DSP7010 USB Drivers


DSP7000 USB Drivers

The correct device drivers are dependent on the unit’s firmware. Please check the version of firmware on your unit and download the appropriate version of drivers.

Firmware Rev AE0 (and all versions preceding)

Firmware Rev AF0 (and all versions succeeding)

Tera Term Application

TeraTerm-4.70


DSP7000 OB Demo

Written in Labview 8.2, this program captures torque and speed data in real time from any Magtrol DSP7000 and displays the data on graphs.  The program uses the new DSP7000 “OB” command to facilitate data capture at rates up to 500 Hz. The source code will automatically be placed on your desktop with installation.  Run “setup” to start the installation.

Note: The driver software that shipped with your DSP7000 must be installed on your computer for this demo to work properly.

Download DSP7000 OB Demo


7500 USB Drivers


MICRO DYNE CALIBRATION

The Micro Dyne Calibration Software walks the user through every step in the calibration process. Simply follow the instructions and prompts that appear on the screen.

Download Micro Dyne Calibration Software


MICRO DYNE USB Drivers


DSP6001 Files

Installation Instructions:
After downloading the desired program, unzip the file and run the setup.exe program. All of the default selections can be used (folder, etc.). After installing the program, restart your computer.


DSP6001 Setup*
This is a “getting started” program to load all of the default parameters for the dynamometer in use. Parameters such as maximum speed, maximum torque, maximum power, encoder, torque filters, PIDs, alarms, etc. will be programmed into the DSP6001 and saved to nonvolatile memory. This allows the user to simply plug in a dynamometer and start operating it with the DSP6001 without going into complicated setup menus. The program will communicate with the DSP6001 by either the Serial or GPIB port (whichever the user has).

Download DSP6001 Setup (620 KB)

*Please Note:
The DSP6001 Setup is a LabVIEW™ program. You must first download and install the RunTime module before using DSP6001 Setup.

Download Runtime (2.54 MB)


LabVIEW VI Drivers

For LabVIEW 2015 or newer.


PSD Software

Download software

DSDSP70DS00 US